基于51單片機的舞蹈機器人步進機仿真設計

部分程序：

#include "reg51.h"

#include "intrins.H"

//8步式步進電機脈沖序列

//unsigned char steps[8] = {0x77,0x33,0xbb,0x99,0xdd,0xcc,0xee,0x66};

unsigned char steps[8] = {0x2,0x6,0x4,0xc,0x8,0x9,0x1,0x3};

//當前各電機在上述序列中的位置

unsigned char cur_step[8] = {0,0,0,0,0,0,0,0};

//這個文件用于記錄舞步信息序列

char speed_tickers[8] = {0,0,0,0,0,0,0,0};

//從上述文件中讀出的當前舞步信息

unsigned char speeds[8] = {0,0,0,0,0,0,0,0};

unsigned char data_pointer = 0;//指向舞步數據的指針

unsigned char time_t = 0;//指定重新讀取一次 speeds 值的計時周期

code char dancedata[] = {54,15,12,12,87,95,65,45,-89,-88,-54,-54,54,68,-45,-65,-65,-48,101,121,115,117,19,

-98,-100,-21,-114,-101,-24,-98,95,102,102,100,130,30,10,-90,-120,87,102,103,105,109,104,-30,-102,-104,-106,110,100,

54,15,12,12,87,95,65,45,-89,-88,-54,-54,-98,95,102,102,100,130,30,10,-90,-120,87,102-114,-101,-24,-98,95,102,102,

100,130,30,10,-90,-120,87,102,102,100,130,30,10,-90,-120,87,102,103,105,54,15,12,12,87,95,65,45,-89,-88,-54,

-98,-100,-21,-114,-101,-24,-98,95,102,102,100,130,30,10,-90,-120,87,102,103,105,12,87,95,65,45,-89,-88,-54,

-98,-100,-21,-114,-101,-24,-98,95,102,102,100,130,30,10,-90,-120,87,102,103,105,109,104,-30,-102,-104,-106,110,

100,130,30,10,-90,-120,87,102,102,100,130,30,10,-90,-120,87,-120,87,102,103,105,109,104,-30,-102,-104,-106,110,

54,15,12,12,87,95,65,45,-89,-88,-54,-54,-98,95,102,102,100,130,30,10,-90,-120,87,102-114,-101,-24,-98,95,102,102,

54,15,12,12,87,95,65,45,-89,-88,-54,-54,-98,95,102,102,100,130,30,10,-90,-120,87,102-114,-101,-24,-98,95,102,102,

54,15,12,12,87,95,65,45,-89,-88,-54,-54,-98,95,102,102,100,130,30,10,-90,-120,87,102-114,-101,-24,-98,95,102,102,

54,15,12,12,87,95,65,45,-89,-88,-54,-54,-98,95,102,102,100,130,30,10,-90,-120,87,102-114,-101,-24,-98,95,102,102,

-98,-100,-21,-114,-101,-24,-98,95,102,102,100,130,30,10,-90,-120,87,102,103,105,12,87,95,65,45,-89,-88,-54,

-98,-100,-21,-114,-101,-24,-98,95,102,102,100,130,30,10,-90,-120,87,102,103,105,12,87,95,65,45,-89,-88,-54,

-98,-100,-21,-114,-101,-24,-98,95,102,102,100,130,30,10,-90,-120,87,102,103,105,12,87,95,65,45,-89,-88,-54,

};

code char pin[8] = {1,2,4,8,16,32,64,128};

char MAX_SPEED_TICKER = 120;

unsigned char i; //電機序號

void SetAllSpeeds(void)? //設置各電機的速度,并讓它運動起來

{

char delta;? //旋轉方向 1:正 -1:反? 0:停

for(i=0;i<8;i++)

{

P2=pin[i]; //發送鎖存信號

speed_tickers[i] += speeds[i]; //計數值增加 speed[i]越高,增加得越多

if(speed_tickers[i] >= MAX_SPEED_TICKER) //如果計數值超過預定最大值,就發送脈沖

{

speed_tickers[i] = 0;

delta = 1;

}

{

speed_tickers[i] = 0;

delta = -1;

}

else delta = 0;

cur_step[i] += delta;

cur_step[i] &= 0x07; //計算當前應發脈沖

P0 = steps[cur_step[i]];

P2 = 0;

}

}

void main()? //程序的入口

{

InitTimer();? //初始化后等中斷

while(1);

}