基于STM32智能窗簾設計proteus仿真

本設計：
基于STM32智能窗簾設計（含源程序+proteus仿真）
仿真：proteus8.11
程序編譯器：keil 5
編程語言：C語言
編號C0007
【騰訊文檔】C0007 網盤鏈接

資料下載鏈接

功能說明：
有手動，自動兩種模式：
1.自動模式：滑動變阻器模擬光照傳感器，通過stm32檢測與閾值比較
低于閾值開窗簾，高于閾值關閉窗簾；

2.手動模式：按鍵控制窗簾關閉打開。

仿真圖（提供源文件）：

源程序（提供源文件）：

#include "delay.h"
#include "sys.h"
#include "adc.h"
#include "1602.h"
#include "motor.h"
#include "bsp_dht11.h"
#define LED1 PAout(13)
#define LED2 PAout(14)
#define MOTOR PCout(0)

unsigned char dis_vol1[] = {"LUX:      % auto"};
unsigned char dis_vol2[] = {"  auto"};
unsigned char dis_vol3[] = {"manual"};
//函數聲明
void display1(void);
void display2(void);
u16    LUX, HZ;
int main(void)
{
    unsigned int i;
    u16 ADCValue1, ADCValue2;
    float voltage1, voltage2;
    u8 Mflag = 2;
    u8 OPENflag = 0;	//起初代表窗簾關
    u8 AUTOflag = 0;	//起初代表自動
    delay_init();
    Adc_Init();
    GPIO_InitStructReadtempCmd();
    MotoR_GPIO();
    lcd_system_reset();
    LED1 = 1;
    LED2 = 0;
    MOTOR = 1;
    while(1)
    {
        ADCValue1 = Get_Adc_Average(ADC_Channel_0, 10);
        voltage1 = ((float)ADCValue1 / 4096) * 3.3; //計算電壓
        LUX = (10000 * voltage1) / 33;
        display1();
        if(PCin(12) == 0) //自動
        {
            AUTOflag = 0;


            for(i = 0; i <6; i++)
                lcd_char_write(i, 1, dis_vol2[i]);
        }
        if(PCin(13) == 0) //手動
        {
            AUTOflag = 1;
            for(i = 0; i < 6; i++)
                lcd_char_write(i, 1, dis_vol3[i]);
        }
        if(PCin(10) == 0 && OPENflag == 0 && AUTOflag == 1)
        {
            LED1 = 0;
            LED2 = 1;
            MOTOR = 0; //開窗簾
            Mflag = 2;
            OPENflag = 1;	 //已經開好
        }
        if(PCin(11) == 0 && OPENflag == 1 && AUTOflag == 1)
        {
            LED1 = 1;
            LED2 = 0;
            MOTOR = 1; //關閉窗簾
            Mflag = 2;
            OPENflag = 0;	 //已經關好

        }
        if(LUX > 400) //40%  閾值
        {
            display1();
            Mflag = 1;		//光照足夠，關閉窗簾
        }
        else
        {
            display1();
            Mflag = 0;	//光照不足，需要啟動窗簾
        }
        if(Mflag == 1 && OPENflag == 1 && AUTOflag == 0)
        {
            LED1 = 1;
            LED2 = 0;
            MOTOR = 1; //關閉窗簾
            Mflag = 2;
            OPENflag = 0;	 //已經關好
        }
        else if(Mflag == 0 && OPENflag == 0 && AUTOflag == 0)
        {
            LED1 = 0;
            LED2 = 1;
            MOTOR = 0; //開窗簾
            Mflag = 2;
            OPENflag = 1;	 //已經開好

        }
    }
}

void display1()
{
    unsigned int i, j;
    dis_vol1[5] = LUX / 100 + 0x30;
    dis_vol1[6] = LUX % 100 / 10 + 0x30;
    dis_vol1[7] = '.';
    dis_vol1[8] = LUX % 10 + 0x30;
    for(i = 0; i < 12; i++)
        lcd_char_write(i, 0, dis_vol1[i]);
    //  	 for(j=0;j<15;j++)
    // 	  lcd_char_write(j,1,dis_vol2[j]);
}

資料清單如下：